Errata in ISO 10846
These are the 2 entries of the errata registry on ISO 10846-2:2008 and ISO 10846-4:2003, in the order the registry lists them. The registry’s introduction says how each claim is checked against the printed page and what the status of an entry means.
ISO 10846-2:2008, 7.6.1 (the unidirectionality pre-run cross-referenced to 6.1, Inequality (1))
Section titled “ISO 10846-2:2008, 7.6.1 (the unidirectionality pre-run cross-referenced to 6.1, Inequality (1))”- Location: clause 7.6.1, “General”, the paragraph on the pre-run that checks the direction of the input motion.
- The print: “A further pre-run shall be performed to check that the acceleration in the excitation direction exceeds the acceleration in other directions. Measurement results, which do not meet the condition of 6.1, Inequality (1), shall be excluded from the evaluation of the dynamic stiffness function.”
- The problem: 6.1, Inequality (1), is the blocked-output condition dB, a level difference between the input and the output sides, which a check of the directions at the input cannot test. The condition the pre-run tests is 6.4, “Unwanted input vibrations”, Inequality (3), dB. The same sentence in the companion parts points to their own unwanted-input clause: ISO 10846-3:2002 7.5.1 to 6.4, ISO 10846-4:2003 7.6.1 to 6.5 and ISO 10846-5:2008 7.6.1 to its Inequality (2). Followed as printed, the sentence excludes the lines where the output is not blocked and keeps those where the input moves in the wrong direction.
- Evidence: the reference read against the clauses it can mean. Verified on PDF page 24 (printed p. 16, 7.6.1), PDF page 20 (printed p. 12, 6.1) and PDF page 21 (printed p. 13, 6.4) of BS EN ISO 10846-2:2008, the UK implementation of ISO 10846-2:2008 (second edition); the companion sentences on PDF page 33 (printed p. 23) of BS EN ISO 10846-3:2002, PDF page 36 (printed p. 26) of BS EN ISO 10846-4:2003 and PDF page 23 (printed p. 15) of BS EN ISO 10846-5:2009.
- Library behaviour: follows the intended target.
check_unwanted_inputjudges the unidirectionality of Part 2 against the 15 dB of its Inequality (3), andcheck_blocked_outputkeeps the 20 dB of Inequality (1) for the output side. The reference changes no number the library reports. - Status: unreported (cross-reference defect, no numerical consequence).
ISO 10846-4:2003, 6.2 NOTE 1 (the bound of Inequality (3) printed as 05 dB)
Section titled “ISO 10846-4:2003, 6.2 NOTE 1 (the bound of Inequality (3) printed as 05 dB)”- Location: clause 6.2, “Measurement of blocking force in the direct method”, NOTE 1 to Inequality (3).
- The print: “Inequality (3) is equivalent to the requirement that dB.”
- The problem: the decimal comma is missing: the bound is 0.5 dB, not 5 dB. Inequality (3) itself, kg, limits the inertia force to 6 % of the measured force, so the two force levels differ by at most dB with the inertia force in phase and dB against it: 0.5 dB, a tenth of what the note reads. ISO 10846-2:2008, which states the same inequality for resilient supports (its Inequality (2)), prints the same note with the comma in place, ” dB”.
- Evidence: the note beside the inequality it restates, and the same note in the companion part. Verified on PDF page 30 (printed p. 20) of BS EN ISO 10846-4:2003, the UK implementation of ISO 10846-4:2003 (first edition), and on PDF page 21 (printed p. 13) of BS EN ISO 10846-2:2008.
- Library behaviour: no change required, since the library computes the
inequality, not the note.
check_output_massreports the bias the mass can cause,bias_bound_db, which is 0.54 dB on the bound, and the conformance check “ISO 10846-4:2003 6.2 NOTE 1” holds it against the 0.5 dB the note means. - Status: unreported.
Created and maintained by José Manuel Requena PlensORCIDAbout the maintainerRelease notesChangelogAll projects