Skip to content

Catalogue of ground surfaces

Key references: Bies et al. 2017 Cox & D'Antonio 2017

The effective flow resistivity every outdoor propagation model asks the ground for, which nobody measures on site. It is not the flow resistivity of the soil: it is the one number that makes a rigid-framed ground model reproduce a measured attenuation, so it carries the model it was fitted with, and the same grass fitted three ways is three rows. Eight of these rows are not measured ground at all but the classes A to H the models define, with the ground factor ISO 9613-2 and NMPB-2008 each take. Cox prints six of his porosities in per cent, from 26.9 to 58.1, in a column that states no unit and prints a fraction on every other row. A porosity of 36.5 is not a porosity, and the page does not say it is a per cent, so those six cells are empty, and the note on each quotes the figure the page prints.

Italic is a value this library worked out; a dotted underline is a cell that is not a plain number, and what it is reads on the cell; an asterisk is a note the page made about the row. Click a mark to read it, or give the table focus and press Enter to walk the marks with the arrow keys.

SurfaceEffective flow resistivity kPa·s/m²PorosityWater content %Porosity decay 1/mISO 9613-2 ground factorNMPB-2008 ground factorSource
Dry snow, newly fallen 0.1 m over about 0.4 m older snow10 to 30Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Sugar snow25 to 50Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Soft forest floor with blueberry greens and moss40Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Forest floor covered by weeds63 to 100Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Pine or hemlock forest floor20 to 80Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Soft forest floor covered with pine needles160Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Sandy forest floor630 to 2 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Dense shrubbery, 20 cm high100Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Soil and bark, sparse vegetation100Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Peat or turf area, homogeneous organic material100Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Soil covered with leaves and twigs160 to 250Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Soil mixed with sawdust250Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Relatively dense soil sparsely covered by grass and other low greens630Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Short grass, green moss and blueberry greens40Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Rough grassland and pasture100 to 300Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Grass, soccer field630 to 2 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Lawn, moderately stepped on160 to 250Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Lawn, seldom stepped on250Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Lawn250 to 400Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Agricultural field160 to 250Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Hard soil400 to 2 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Soil, exposed and rain packed4 000 to 8 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Wet, sandy loam1 500Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Moistened sand500Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Bare sandy plain250 to 500Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Dry sand60 to 140Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Sandy silt, hard packed by vehicles800 to 2 500Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Quarry dust, hard packed by vehicles5 000 to 20 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Mixed paving stones and grass630 to 2 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Old gravel field with sparse vegetation2 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Gravel road, stones and dust2 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Gravel parking lot630 to 2 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Asphalt sealed by dust and light use30 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Concrete20 000Bies 5e Table 5.1, PDF page 256 (printed p. 227)
Very soft (snow or moss)12.511Bies 5e Table 5.2, PDF page 257 (printed p. 228)
Soft forest floor31.511Bies 5e Table 5.2, PDF page 257 (printed p. 228)
Uncompacted, loose ground8011Bies 5e Table 5.2, PDF page 257 (printed p. 228)
Normal uncompacted ground (pastures, forest floors) Description wrapped over two printed lines: "Normal uncompacted ground" / "(pastures, forest floors)".20011Bies 5e Table 5.2, PDF page 257 (printed p. 228)
Compacted fields, lawns and gravel50000.7Bies 5e Table 5.2, PDF page 257 (printed p. 228)
Compacted dense ground (gravel road, parking lot) Description wrapped over two printed lines: "Compacted dense ground" / "(gravel road, parking lot)".2 00000.3Bies 5e Table 5.2, PDF page 257 (printed p. 228)
Asphalt, concrete20 00000Bies 5e Table 5.2, PDF page 257 (printed p. 228)
Water Class H is water, not a ground surface in the porous sense; the page still gives it a representative flow resistivity, 200000 kPa s/m2, which is an acoustically hard limit rather than a measured value.200 00000Bies 5e Table 5.2, PDF page 257 (printed p. 228)
Snow Dry snow, newly fallen 0.1 m over about 0.4 m older snow Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.10 to 30Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Snow Snow The water content and porosity decay cells are blank, not dashed.5 to 160.5 to 0.9Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Snow Sugar snow Water content, porosity and porosity decay cells all print a dash.25 to 50Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Snow Snow (new) Water content cell prints a dash.1 to 100.64 to 0.880 to 3Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Snow Snow (old crusted) Water content cell prints a dash.8 to 300.50 to 100Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Snow Snow (Great Himalaya snowpack) The water content and porosity decay cells are blank, not dashed.1 to 230.52 to 0.89Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Forests and crops In forest, pine, or hemlock Water content, porosity and porosity decay cells all print a dash.20 to 80Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Forests and crops Forest floor Flow resistivity printed "7 × 10^3–20 × 10^4", the two ends written with different exponents. Water content cell prints a dash.7 to 2000.4 to 0.80 to 40Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Forests and crops Mineral layer beneath mixed deciduous forest Flow resistivity printed "(540 ± 92) × 10^3". Name wrapped over two printed lines. Porosity decay cell prints a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).540 ± 9215Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Forests and crops Humus on pine forest floor Flow resistivity printed "(230 ± 220) × 10^3"; the stated uncertainty is almost as large as the value. Porosity decay cell prints a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).230 ± 22016.1Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Forests and crops Litter layer on mixed deciduous forest floor (2–5 cm thick) Flow resistivity printed "(30 ± 30) × 10^3"; the stated uncertainty equals the value. Name wrapped over two printed lines, the en dash of "2–5 cm" as printed. Water content, porosity and porosity decay cells all print a dash.30 ± 30Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Forests and crops Pine forest litter (6–7 cm thick) Flow resistivity printed "(9 ± 5) × 10^3"; the en dash of "6–7 cm" as printed. Porosity decay cell prints a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).9 ± 528.6Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Forests and crops Tall crops Water content and porosity cells print a dash.40 to 500Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Sports field Fitted using Delany and Bazley model First of three fitted values printed for this surface, marked [a]. The porosity cell, "0.24", and the porosity decay cell, "−270", are printed once for the surface, on this line, and carry no fit marker. The water content cell is blank.1 4000.24-270Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Sports field Fitted using semi-phenomenological model Second of three fitted values printed for this surface, marked [b]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.510Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Sports field Fitted using variable porosity model Third of three fitted values printed for this surface, marked [c]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.990Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Lawn Fitted using Delany and Bazley model First of three fitted values printed for this surface, marked [a]. The porosity cell is printed "0.34–1 [b]": the range itself carries the marker [b] = Fitted using semi-phenomenological model. The porosity decay cell, printed "−76 to 47", carries no marker. Both are printed once for the surface, on this line. The water content cell is blank.120 to 7500.34 to 1-76 to 47Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Lawn Fitted using semi-phenomenological model Second of three fitted values printed for this surface, marked [b]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.120 to 310Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Lawn Fitted using variable porosity model Third of three fitted values printed for this surface, marked [c]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.39 to 370Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Long grass Fitted using Delany and Bazley model First of three fitted values printed for this surface, marked [a]. The porosity cell is printed "0.38–1 [b]": the range itself carries the marker [b] = Fitted using semi-phenomenological model. The porosity decay cell, printed "−9 to 48", carries no marker. Both are printed once for the surface, on this line. The water content cell is blank.47 to 1800.38 to 1-9 to 48Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Long grass Fitted using semi-phenomenological model Second of three fitted values printed for this surface, marked [b]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.37 to 85Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Long grass Fitted using variable porosity model Third of three fitted values printed for this surface, marked [c]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.140 to 800Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Grassland Two flow resistivity ranges are printed on two lines for this one surface, "7 × 10^4–8.5 × 10^5" and "1 × 10^5–2.4 × 10^5", with no fit markers and nothing to pair them with, so both go to reported. Water content cell prints a dash.70 to 850, 100 to 2400.3 to 0.70 to 250Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Pasture Fitted using Delany and Bazley model First of three fitted values printed for this surface, marked [a]. The porosity cell is printed "0.2–1 [b]": the range itself carries the marker [b] = Fitted using semi-phenomenological model. The porosity decay cell, printed "−400 to 80", carries no marker. Both are printed once for the surface, on this line. The water content cell prints a dash.110 to 1 1000.2 to 1-400 to 80Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Pasture Fitted using semi-phenomenological model Second of three fitted values printed for this surface, marked [b]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.100 to 950Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Pasture Fitted using variable porosity model Third of three fitted values printed for this surface, marked [c]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.25 to 820Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Grass, rough pasture, airport, public buildings, etc. Flow resistivity printed "15 × 10^4–30 × 10^4". Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.150 to 300Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Grass Grass root layer in loamy sand Flow resistivity printed "(150 ± 90) × 10^3" and porosity printed "48 ± 4", the only porosity cell in the table with a stated uncertainty. Water content and porosity decay cells print a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).150 ± 90Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Earth, exposed and rain-packed Water content, porosity and porosity decay cells all print a dash.4 000 to 8 000Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Bare earth Fitted using Delany and Bazley model First of three fitted values printed for this surface, marked [a]. The porosity cell is printed "0.4 [b]": the value itself carries the marker [b] = Fitted using semi-phenomenological model. The porosity decay cell, printed "−49", carries no marker. Both are printed once for the surface, on this line. The water content cell is blank.6700.4-49Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Bare earth Fitted using semi-phenomenological model Second of three fitted values printed for this surface, marked [b]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.390Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Bare earth Fitted using variable porosity model Third of three fitted values printed for this surface, marked [c]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.370Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Loose sand or dry cultivated soil Water content cell prints a dash.30 to 3100.36 to 0.520 to 10Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Sandy silt, hard packed by vehicles Last row of the table on the first printed page (folio 200, which ends with "(Continued)"). Water content, porosity and porosity decay cells all print a dash.800 to 2 500Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Arable Fitted using Delany and Bazley model First row of the continuation page (folio 201); the group heading Earth is not repeated there, so the group is carried over from the first page. First of three fitted values printed for this surface, marked [a]. The porosity cell is printed "0.15–1 [b]": the range itself carries the marker [b] = Fitted using semi-phenomenological model. The porosity decay cell, printed "−490 to 81", carries no marker. Both are printed once for the surface, on this line. The water content cell is blank.93 to 1 9000.15 to 1-490 to 81Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Arable Fitted using semi-phenomenological model Second of three fitted values printed for this surface, marked [b]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.75 to 1 600Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Arable Fitted using variable porosity model Third of three fitted values printed for this surface, marked [c]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.22 to 1 700Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Cultivated soil The water content and porosity decay cells are blank, not dashed.100 to 2 0000.4 to 0.6Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Wet and compacted soil Water content and porosity cells print a dash.40 000-200 to 0Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Heath Fitted using semi-phenomenological model First of three fitted values printed for this surface. TWO defects on the printed line, both transcribed as printed and neither repaired: (1) the low end of the range is printed "1.7.3 × 10^5", with two decimal points, which is not a readable number, so the whole flow resistivity cell goes to unquantified rather than being guessed at; (2) the fit marker is printed [b], not [a], although every other surface with three fitted lines in this table is marked [a], [b], [c] in that order and the line below is also marked [b]. The porosity cell is printed "0.71–1 [b]": the range itself carries the marker [b] = Fitted using semi-phenomenological model. The porosity decay cell, printed "17–33", carries no marker. Both are printed once for the surface, on this line. The water content cell is blank.1.7.3 × 10⁵ – 3.2 × 10⁵0.71 to 117 to 33Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Heath Fitted using semi-phenomenological model Second of three fitted values printed for this surface, marked [b]. The line above is marked [b] as well; see that row. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.180 to 260Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Earth Heath Fitted using variable porosity model Third of three fitted values printed for this surface, marked [c]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.51 to 110Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Rock Roadside dirt, ill-defined, small rocks up to 0.1 m mesh Flow resistivity printed "30 × 10^4–80 × 10^4". Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.300 to 800Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Rock Clean limestone chops, thick layer (1–2.5 cm mesh) The word "Clean" is printed in italic, the rest of the name upright. Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.1 000 to 4 000Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Rock Old dirt roadway, fine stones (5 cm mesh) interstices filled Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.2 000 to 4 000Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Rock Gravel Flow resistivity printed "1.5 × 10^3–59 × 10^3". Water content and porosity decay cells print a dash.1.5 to 590.3 to 0.4Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Other Quarry dust fine, very hard-packed by vehicles Flow resistivity printed "5 × 10^6–20 × 10^6". Name wrapped over two printed lines. Water content, porosity and porosity decay cells all print a dash.5 000 to 20 000Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Other Asphalt, sealed by dust and light use Flow resistivity printed "≈3 × 10^7" with a printed approximately-equal sign, the only approximate cell in the table. Water content, porosity and porosity decay cells all print a dash.30 000Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Other Porous asphalt, new Flow resistivity printed "2 × 10^3–15 × 10^3". Water content and porosity decay cells print a dash.2 to 150.15 to 0.3Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Other Urban Fitted using Delany and Bazley model First of three fitted values printed for this surface, marked [a]. The porosity cell is printed "0.61–1 [b]": the range itself carries the marker [b] = Fitted using semi-phenomenological model. The porosity decay cell, printed "0–25", carries no marker. Both are printed once for the surface, on this line. The water content cell prints a dash.41 to 670.61 to 10 to 25Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Other Urban Fitted using semi-phenomenological model Second of three fitted values printed for this surface, marked [b]; it is a single value where the other two lines are ranges. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.35Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Other Urban Fitted using variable porosity model Third of three fitted values printed for this surface, marked [c]. Water content, porosity and porosity decay are printed once for this surface, on the line of the first fitted value; see that row.21 to 67Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Coarse sand, pore size 98 μm water content 0 % First of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.500-14Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Coarse sand, pore size 98 μm water content 11 % Second of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.10011-82Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Coarse sand, pore size 98 μm water content 51 % Third of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.47051-141Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Coarse sand, pore size 98 μm water content 95 % Fourth of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The flow resistivity falls back at the highest water content, below the 51 % and 11 % lines. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.90951 290Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Fine sand Water content and porosity decay cells print a dash. Printed name is "Fine sand" with no pore size, distinct from the "Fine sand, pore size 65 μm" block below it.3100.44Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Fine sand, pore size 65 μm water content 0 % First of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.1500-28Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Fine sand, pore size 65 μm water content 15 % Second of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.14015130Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Fine sand, pore size 65 μm water content 48 % Third of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.15048620Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Fine sand, pore size 65 μm water content 95 % Fourth of four. One of four lines printed under this one surface name, one per water content; the water content is the only thing that distinguishes them. Porosity cell prints a dash. The text on folio 215 (PDF page 272) says Horoshenkov and Mohamed found the two-parameter model of Attenborough more suitable for these sands than one based on the Delany and Bazley formulations, and that these are the parameters of that model they deduced.41951 130Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Loamy sand Flow resistivity printed "(420 ± 17) × 10^3". Porosity decay cell prints a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).420 ± 1711.2Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)
Sand Bare sandy plain Flow resistivity printed "(370 ± 110) × 10^3". Last row of the table. Porosity decay cell prints a dash. The Porosity column prints this value as a number far above 1 while every other row of the column prints a fraction; on the page it is plainly a percentage, but the page does not say so, and the cell is held as misprinted (docs/ERRATA.md).370 ± 1109.3Cox & D'Antonio 3e Table 6.7, PDF pages 257-258 (printed pp. 200-201)

  • Bies, D. A., Hansen, C. H., & Howard, C. Q. (2017). Engineering noise control (5th ed.). CRC Press. https://doi.org/10.1201/9781351228152 Tables 5.1 and 5.2: the source of the rows of the catalogue of ground surfaces that cite it.
  • Cox, T. J., & D'Antonio, P. (2017). Acoustic absorbers and diffusers: Theory, design and application (3rd ed.). CRC Press. https://doi.org/10.1201/9781315369211 Table 6.7: the source of the rows of the catalogue of ground surfaces that cite it.