Errata in Ainslie (2010)
These are the 2 entries of the errata registry on Ainslie (2010), in the order the registry lists them. The registry’s introduction says how each claim is checked against the printed page and what the status of an entry means.
Ainslie (2010), Equation (4.6) vs its own folio 177, and the exponent of Equation (4.13)
Section titled “Ainslie (2010), Equation (4.6) vs its own folio 177, and the exponent of Equation (4.13)”-
Location: Principles of Sonar Performance Modelling (Springer 2010), Equation (4.6) on printed folio 127; the sea-water density quoted in Section 4.4 on printed folio 177; Equation (4.13) on printed folio 135.
-
The print: Equation (4.6) gives the density of sea water as , attributed to Pierce (1989, p. 34), with the units fixed by Equations (4.7) to (4.10) on folio 128: pressure in pascals, temperature in degrees Celsius, density in . Equation (4.4) on folio 127 defines that pressure as , and Equation (4.11) on folio 128 evaluates it to Pa at the surface. Folio 177 then states, for the ratios that scale the Bachman sediment correlations, “standard conditions involving atmospheric pressure, a temperature of 23 °C, and salinity 35” with .
-
The problem: two defects, of different kinds.
(a) The 1024.2 of folio 177 does not follow from Equation (4.6) read with Equation (4.4). At 23 °C, salinity 35 and one atmosphere the equation gives 1024.287 9, which prints as 1024.3. The printed 1024.2 is what the equation gives with its pressure term set to zero, that is, reading as a gauge pressure against the definition the same chapter states. The difference is , or 4.3 parts in a hundred thousand.
(b) Equation (4.13), which rearranges (4.6) to estimate salinity from a measured density, prints the pressure coefficient as where (4.6) has . Two orders of magnitude, and not a restatement of a different quantity: it is the same coefficient in the same role. Carried through at 23 °C it gives against 1024.29, an error of 0.42 %.
-
Evidence: Equation (4.6) evaluated at the stated conditions with the pressure of Equation (4.11), against the value folio 177 prints; and the two printed exponents compared directly. Verified on PDF pages 157, 158, 165 and 207 (printed pp. 127, 128, 135 and 177) of the Springer 2010 edition.
-
Library behaviour: implements Equation (4.6) with the absolute pressure its own Equation (4.4) defines, because a printed definition outranks a rounded quotation of a derived value three chapters later. The discrepancy is below every tolerance in this library, so nothing turns on the choice; what would have turned on it is picking a side silently. Equation (4.13) is not implemented (
tests/fluids/test_water.py, conformance checks “Sea water (Ainslie 2010)”). -
Status: unreported.
Ainslie, Principles of Sonar Performance Modelling (2010), Eq. (9.57)
Section titled “Ainslie, Principles of Sonar Performance Modelling (2010), Eq. (9.57)”Textbook, not a standard.
-
Location: Section 9.1.1.2.4 (printed p. 457), the transition range between the mode-stripping and single-mode regimes of the Weston flux model.
-
The print: , where is the water depth, the Weston effective depth of Eq. (9.55), and the reflection loss gradient.
-
The problem: the sentence immediately above it prescribes the derivation, “estimated by equating θ_n and θ_eff with n = 3/2”. The two angles are four printed pages apart, not on the same page as an earlier revision of this entry stated:
- Eq. (9.47), , printed p. 453, with the true water depth (it comes from the multipath integral Eq. (9.46), whose prefactor is the cylinder area of Eq. (9.44), so is the depth that counts bottom bounces);
- Eq. (9.56), , printed p. 457, with the effective depth (mode angles are set by the apparent pressure-release boundary).
Equating them at gives , that is . The printed form is larger by . The factor is unconditional: it survives even if is substituted for in Eq. (9.47), which is presumably how the printed arose, and that reading would give , still below the print. The residual is the depth substitution itself, and it tends to 1 at high frequency. The other transition of the same section, Eq. (9.50) , follows its own derivation exactly (it is where Eq. (9.42) and Eq. (9.49) cross), so the defect is confined to Eq. (9.57).
-
Evidence: the symbolic re-derivation above, checked numerically for , , over the Table 9.1 sand seabed (, , , ):
there (Eq. 9.47) derivation, 19.9 km 4.808° printed Eq. (9.57), 67.1 km 2.619° The ratio is to every digit carried. The angle column is an independent check that does not depend on how the derivation is read: the first two mode angles of Eq. (9.56) are and , so . At the derived range the effective angle is exactly , halfway between the first two modes, which is what the text asks for. At the printed range it has fallen to 2.619°, below itself: the second mode would have been stripped long before, so that range cannot be where the single-mode regime begins. Both printed formulae are confirmed on PDF page 483 (printed p. 453) and PDF page 487 (printed p. 457) of Ainslie, Principles of Sonar Performance Modelling (2010).
-
Library behaviour:
weston_regime_boundariesinpropagation/weston_regimes.pyimplements the derivation-consistent , which is also what keeps defined with everywhere the module evaluates Eq. (9.47). The equating rule is pinned bytest_mode_stripping_boundary_equates_theta_eff_with_mode_3_over_2, which rebuilds both angles from the printed equations rather than from the implementation, and the shared definition of bytest_composite_loss_and_the_boundary_use_the_same_effective_angle(both intests/underwater/propagation/test_weston_regimes.py). -
Status: unreported (textbook rather than a standard).