# Errata in ISO 8297

> One page of the phonometry documentation, as Markdown. Index: https://docs.jmrp.io/phonometry/llms.txt

Canonical: https://docs.jmrp.io/phonometry/reference/errata/iso-8297/
Language: en
Alternate: https://docs.jmrp.io/phonometry/es/reference/errata/iso-8297/index.md
Version: phonometry 4.0.0
Install: pip install "phonometry[full]"
Author: José Manuel Requena Plens (https://orcid.org/0000-0003-1250-6212)
Published: 2026-10-28
Updated: 2026-11-16T21:36:14Z
License: MIT (https://github.com/jmrplens/phonometry/blob/main/LICENSE)
Summary: Errata in ISO 8297: 4 defects in the printed text, with the evidence and what phonometry does about each.

---

These are the 4 entries of the [errata registry](https://docs.jmrp.io/phonometry/reference/errata/) on ISO 8297:1994, in the order the registry lists them. The registry's introduction says how each claim is checked against the printed page and what the status of an entry means.

## ISO 8297:1994, 3.7 (a misspelt term in the heading of the definition)

- **Location:** definition 3.7 (PDF page 11, printed p. 3) of BS ISO
  8297:1994, the identical British adoption of ISO 8297:1994.
- **The print:** "characteristics height of the plant, $H$".
- **The problem:** "characteristics" for "characteristic". The symbol list of
  clause 4 on the same page ("Characteristic height of the plant, in metres")
  and 9.2 c) (PDF page 13, printed p. 5: "the characteristic height of the
  plant, $H$") write the term without the extra letter; the heading of the
  definition is the one place that names it otherwise.
- **Evidence:** Verified on PDF page 11 (printed p. 3) of BS ISO 8297:1994,
  definition 3.7, against the symbol list of clause 4 on the same page and
  9.2 c) on PDF page 13 (printed p. 5).
- **Library behaviour:** none to take; no number depends on it. The height is
  `plant_characteristic_height_m` and the `characteristic_height_m` of the
  contour.
- **Status:** unreported.

## ISO 8297:1994, 9.1.1 b) (the aspect angle written with the symbol of the microphone's 3 dB angle)

- **Location:** clause 9.1.1 b) (PDF page 13, printed p. 5), against the
  symbol list of clause 4 (PDF page 11, printed p. 3), the aspect-angle
  callout of Figure 1 and clause 7.1 (PDF page 12, printed p. 4) of BS ISO 8297:1994, the
  identical British adoption of ISO 8297:1994.
- **The print:** "from any point on the measurement contour, the plant area
  shall be seen inside an aspect angle, $\theta$, not greater than 180°
  (see Figure 1)".
- **The problem:** clause 4 gives the two angles of the standard two
  symbols: $\theta$ is the "Angle at which the sensitivity of a directional
  microphone has fallen by 3 dB", the angle 7.1 requires to exceed ±30° and
  10.6 puts in $\Delta L_\mathrm{M} = 3(1 - \theta/90)$ dB, and $\phi$ is
  the "Aspect angle subtended at a microphone position by the extremities of
  the perimeter of the plant area". Figure 1, to which 9.1.1 b) refers, labels
  the aspect angle $\phi$. The clause therefore writes the aspect angle with
  the symbol of the microphone's angle. Figure 1 also writes the bound as
  "$\phi < 180°$", strict, where the clause says "not greater than 180°".
- **Evidence:** Verified on PDF page 13 (printed p. 5) of BS ISO 8297:1994,
  clause 9.1.1 b), against the symbol list on PDF page 11 (printed p. 3) and
  Figure 1 and clause 7.1 on PDF page 12 (printed p. 4).
- **Library behaviour:** the aspect angle is $\phi$ of clause 4 and
  Figure 1, and the bound is the clause's, at most 180°
  (`check_plant_measurement`, requirement `aspect_angle`, and
  `PlantMeasurementContour.aspect_angles_deg`); $\theta$ keeps its clause 4
  meaning as `directional_microphone_angle_deg`. No change was required.
- **Status:** unreported.

## ISO 8297:1994, 10.4 (the area term written with a lower-case subscript)

- **Location:** clause 10.4, step 4 (PDF page 15, printed p. 7) of BS ISO
  8297:1994.
- **The print:** "Calculate an area term, $\Delta L_\mathrm{s}$, in decibels,
  for the measurement surface (as defined in ISO 3744)".
- **The problem:** the equation directly below the sentence writes
  $\Delta L_\mathrm{S} = 10 \lg[(2S_\mathrm{m} + hl)/S_0]$ dB with a capital
  subscript, and so do the symbol list of clause 4 (PDF page 11, printed p. 3:
  "$\Delta L_\mathrm{S}$ Area term, in decibels") and the sum of 10.8 on the
  same page. The prose of 10.4 is the only place that writes the subscript in
  lower case; steps 5 to 7 name their terms with the symbols their equations
  use.
- **Evidence:** Verified on PDF page 15 (printed p. 7) of BS ISO 8297:1994,
  clause 10.4, against its own equation and 10.8 on the same page and the
  symbol list on PDF page 11 (printed p. 3). The running text of this reprint
  is set apart from its equations, so the slip may belong to the British
  adoption rather than to ISO 8297:1994.
- **Library behaviour:** none to take; the term is
  `PlantSoundPowerResult.area_term_db`, written $\Delta L_\mathrm{S}$ in its
  docstring.
- **Status:** unreported.

## ISO 8297:1994, Table 3 (the 31.5 Hz octave printed as 31 Hz)

- **Location:** Table 3, first row (PDF page 15, printed p. 7) of BS ISO
  8297:1994.
- **The print:** the first octave-band centre frequency of Table 3 is "31".
- **The problem:** 7.2 requires the centre frequencies of the bands to
  "correspond to those of ISO 266", whose octave band is 31.5 Hz, and NOTE 8
  (PDF page 14, printed p. 6) names the same band "31,5 Hz". The row is the
  31.5 Hz octave; its value, 0 dB/m, is unaffected.
- **Evidence:** Verified on PDF page 15 (printed p. 7) of BS ISO 8297:1994,
  Table 3, against clause 7.2 on PDF page 13 (printed p. 5) and NOTE 8 on PDF
  page 14 (printed p. 6).
- **Library behaviour:** `PLANT_AIR_ABSORPTION_DB_PER_M` keys the row as
  31.5 Hz, the band the rest of the method names. No change of any value was
  required.
- **Status:** unreported.
