# Psychoacoustic annoyance and fluctuation strength

> One page of the phonometry documentation, as Markdown. Index: https://docs.jmrp.io/phonometry/llms.txt

Canonical: https://docs.jmrp.io/phonometry/perception/psychoacoustics/psychoacoustic-annoyance/
Language: en
Alternate: https://docs.jmrp.io/phonometry/es/perception/psychoacoustics/psychoacoustic-annoyance/index.md
Version: phonometry 4.0.0
Install: pip install "phonometry[full]"
Author: José Manuel Requena Plens (https://orcid.org/0000-0003-1250-6212)
Published: 2026-07-12
Updated: 2026-11-16T21:36:10Z
License: MIT (https://github.com/jmrplens/phonometry/blob/main/LICENSE)
Summary: Fastl & Zwicker psychoacoustic annoyance (loudness, sharpness, roughness, fluctuation strength), its AM-noise closed form and the Osses 2016 model.

---

How *annoying* a sound is depends on more than how loud it is. Fastl & Zwicker,
*Psychoacoustics: Facts and Models*, combine four psychoacoustic sensations
(**loudness**, **sharpness**, **roughness** and **fluctuation strength**) into a
single **psychoacoustic annoyance** $PA$, a scalar that grows with loudness and
is lifted further when the sound is sharp, rough or slowly fluctuating. This page
covers the exact $PA$ model (Eqs 16.2–16.4), the **fluctuation strength** it
consumes, both the closed form for amplitude-modulated broadband noise
(Eq. 10.2) and the Osses et al. (2016) signal model, and the signal
convenience that derives all four sensations from a recording.

![Psychoacoustic annoyance PA against percentile loudness N5 for three sensation profiles: a neutral baseline where PA equals N5, a sharp sound and a rough-and-fluctuating sound both lifted above the baseline, with the worked example PA = 37.05 marked](https://docs.jmrp.io/phonometry/media/psychoacoustic_annoyance.svg)

**Show the code for this figure**

```python
import matplotlib.pyplot as plt
import numpy as np
from phonometry import psychoacoustics

n5 = np.linspace(4.0, 60.0, 200)
profiles = [
    ("Baseline: S = 1.75 acum, F = R = 0", 1.75, 0.0, 0.0),
    ("Sharp: S = 3.5 acum", 3.5, 0.0, 0.0),
    ("Rough + fluctuating: F = 1.2 vacil, R = 0.7 asper", 2.0, 1.2, 0.7),
]
fig, ax = plt.subplots()
for label, s, f, r in profiles:
    pa = [psychoacoustics.psychoacoustic_annoyance(v, s, f, r).annoyance for v in n5]
    ax.plot(n5, pa, label=label)

ex = psychoacoustics.psychoacoustic_annoyance(30.0, 2.0, 0.5, 0.3)
ax.plot([30.0], [ex.annoyance], "o", label=f"Worked example (PA = {ex.annoyance:.2f})")
ax.set_xlabel("Percentile loudness N5 [sone]")
ax.set_ylabel("Psychoacoustic annoyance PA")
ax.legend()
plt.show()
```

## 1. The four sensations

Psychoacoustic annoyance rests on four hearing sensations, each with its own
model and unit in the library:

- **Loudness**: the percentile loudness $N_5$ (the loudness exceeded 5 % of the
  time), in **sone**, from the ISO 532-1 Zwicker time-varying model
  (`loudness_zwicker`, see [Loudness](https://docs.jmrp.io/phonometry/perception/psychoacoustics/loudness/)).
- **Sharpness** $S$, in **acum**: the spectral balance towards high
  frequencies, DIN 45692 (`sharpness_din`).
- **Roughness** $R$, in **asper**: the harshness of fast (~70 Hz) amplitude
  modulation, ECMA-418-2 Sottek model (`roughness_ecma`).
- **Fluctuation strength** $F$, in **vacil**: the sensation of slow (~4 Hz)
  loudness fluctuation (§3 below).

## 2. Psychoacoustic annoyance (Eqs 16.2–16.4)

The exact model (Fastl & Zwicker Eq. 16.2; origin Widmann 1992) scales $N_5$
by a factor that grows with the sharpness weighting $w_S$ and the combined
roughness/fluctuation weighting $w_{FR}$:

$$
PA = N_5\left(1 + \sqrt{w_S^2 + w_{FR}^2}\right), \qquad
w_S = (S - 1.75)\,0.25\,\log_{10}(N_5 + 10)\ \ (S > 1.75\ \mathrm{acum}), \qquad
w_{FR} = \frac{2.18}{N_5^{0.4}}\,(0.4\,F + 0.6\,R).
$$

$w_S$ is zero for $S \le 1.75\ \text{acum}$ (sharpness only adds annoyance
above that threshold); $w_{FR}$ weights roughness more heavily than
fluctuation strength (0.6 vs 0.4). Those two choices are the whole of the
modelling judgement in the formula, and they are easier to trust once seen:

![Left: the sharpness weighting wS against sharpness from 1 to 5 acum for percentile loudnesses of 10, 30 and 60 sone, flat at zero below 1.75 acum and fanning out above it. Right: psychoacoustic annoyance against a sensation magnitude spent entirely on roughness or entirely on fluctuation strength at a fixed loudness of 30 sone and sharpness of 2 acum, the roughness curve rising to 45.4 against 40.5 for fluctuation strength at a magnitude of 1.5](https://docs.jmrp.io/phonometry/media/annoyance_weightings.svg)

*A sound has to be sharper than the 1.75 acum reference before sharpness costs
anything at all, and the fan above that point is the loudness dependence of
$w_S$. On the right, the same sensation magnitude buys about half again as much
annoyance when it arrives as roughness rather than as fluctuation strength.*

**Show the code for this figure**

```python
import matplotlib.pyplot as plt
import numpy as np

# `psychoacoustics` is imported by the snippet above.
sharpness = np.linspace(1.0, 5.0, 200)
for n5 in (10.0, 30.0, 60.0):
    w_s = [psychoacoustics.psychoacoustic_annoyance(n5, float(s), 0.0, 0.0).w_s
           for s in sharpness]
    plt.plot(sharpness, w_s, label=f"N5 = {n5:g} sone")
plt.axvline(1.75, linestyle="--")
plt.xlabel("Sharpness S [acum]")
plt.ylabel("Sharpness weighting wS")
plt.legend()
plt.show()

# The same magnitude spent on roughness or on fluctuation strength, at a
# fixed N5 = 30 sone and S = 2.0 acum:
rough = psychoacoustics.psychoacoustic_annoyance(30.0, 2.0, 0.0, 1.5).annoyance
fluct = psychoacoustics.psychoacoustic_annoyance(30.0, 2.0, 1.5, 0.0).annoyance
print(round(rough, 1), round(fluct, 1))   # 45.4 40.5
```

`psychoacoustic_annoyance` takes the four quantities directly and
returns the annoyance together with the two intermediate weightings:

```python
from phonometry import psychoacoustics

res = psychoacoustics.psychoacoustic_annoyance(30.0, 2.0, 0.5, 0.3)   # N5, S, F, R
print(round(res.annoyance, 4))   # 37.0477
print(round(res.w_s, 4), round(res.w_fr, 4))   # 0.1001 0.2125

res.plot()   # PA beside its wS and wFR weightings (needs matplotlib)
```

**What that number means.** $PA$ carries no unit and no criterion. It is built
so that a neutral sound (sharpness at or below 1.75 acum, no roughness, no
fluctuation) has a $PA$ equal to its $N_5$ in sone, and every sharp, rough or
fluctuating quality can only push it *above* that floor. So read $PA$ as "the
loudness this sound is worth once its character is taken into account": the
worked example's 37.05 against an $N_5$ of 30 sone says the character costs
23 %. Comparison is the point (rank two designs of the same product, or
quantify what a fix bought), and no limit exists to quote it against.

**Caution**

**This is not the annoyance of environmental-noise assessment.** Psychoacoustic
annoyance is a laboratory scaling of a single sound. It says nothing about
long-term exposure, time of day, the attitude of the population towards the
source, or the percentage highly annoyed, which is the business of the rating
levels and exposure-response relations in
[Environmental Levels](https://docs.jmrp.io/phonometry/environment/assessment/environmental-levels/).
A $PA$ of 37 is not "37 % highly annoyed", and the two quantities are not
convertible.

The figure above sweeps $PA$ against $N_5$ for three profiles: a neutral
baseline ($S = 1.75\ \text{acum}$, $F = R = 0$, so $PA = N_5$), a sharp sound
and a
rough-and-fluctuating sound, both lifted above the baseline, with the worked
example marked.

The model is small enough to draw whole: two weightings and one combination.
The diagram traces the worked example through it, sensation by sensation.

![Block diagram of the Fastl and Zwicker psychoacoustic annoyance model: the four sensations of the worked example, sharpness of 2.0 acum, percentile loudness N5 of 30 sone, fluctuation strength of 0.5 vacil and roughness of 0.3 asper, feed two weightings, the sharpness weighting wS of 0.1001 that is zero below 1.75 acum and the roughness-and-fluctuation weighting wFR of 0.2125 that weighs roughness 0.6 against 0.4, and combine into PA equal to N5 times one plus the root of wS squared plus wFR squared, giving 37.05; a closing note recalls that a neutral sound sits on the baseline PA equal to N5](https://docs.jmrp.io/phonometry/media/diagram_psychoacoustic_annoyance.svg)

### 2.1 From a signal (engineering estimate)

`psychoacoustic_annoyance_from_signal` is a convenience that derives all four
sensations from a calibrated pressure signal and combines them: $N_5$ from the
ISO 532-1 Zwicker time-varying loudness, $S$ from DIN 45692 sharpness, $R$
from the ECMA-418-2 Sottek roughness and $F$ from the fluctuation-strength
signal model.

The convenience is only as good as the record it is given, and neither entry
point on this page takes a calibration argument, so `x` must already be
**calibrated pressure in pascals**; see
[Measuring the input](https://docs.jmrp.io/phonometry/perception/psychoacoustics/loudness/#measuring-the-input-clause-4)
on the loudness page for how that factor is obtained. Beyond calibration:
unweighted; one declared operating state rather than a run-up; long enough that
$N_5$ is a percentile of something and that the ~4 Hz fluctuation analysis has
enough modulation periods, which in practice means several seconds and the same
length for every design being compared; and `field=` matching how the sound was
captured. A two-second clip yields an $N_5$ that is nearly $N_\text{max}$ and an
$F$ biased low. A binaural or artificial-head recording is analysed one ear at a
time, already equalized to the free or diffuse field, and the louder channel is
the one usually reported.

```python
import numpy as np
from phonometry import psychoacoustics

# A raw recording plus its calibration so the guide runs standalone. There is
# no calibration_factor argument here, so x must already be in pascals.
fs = 48000
t = np.arange(int(5.0 * fs)) / fs
x = (1.0 + 0.8 * np.sin(2 * np.pi * 4.0 * t)) * np.sin(2 * np.pi * 1000 * t)
x *= 2e-5 * 10 ** (70 / 20) / np.sqrt(np.mean(x**2))   # calibrated to 70 dB SPL

res = psychoacoustics.psychoacoustic_annoyance_from_signal(x, fs, field="free")
print(f"PA = {res.annoyance:.1f}  (N5 = {res.n5:.1f} sone, S = {res.sharpness:.2f} acum,"
      f" R = {res.roughness:.2f} asper, F = {res.fluctuation_strength:.2f} vacil)")

res.plot()   # the same PA / wS / wFR view, now from the four derived sensations
```

All four sensations must come from the *same* record and the same operating
state: PA is a combination rule, not a measurement in its own right, so
computing $N_5$ over a minute and $R$ over two seconds of it silently mixes two
different sounds. Quote each sensation with the model that produced it.

**Caution**

**Model-mixing caveat.** This composite mixes model families: Zwicker-family $N_5$ and $S$, Sottek $R$
and Osses $F$. The $PA$ model was calibrated with Zwicker-family sensations, so
treat the signal convenience as an *engineering estimate*. For exact,
reproducible results, compute the four quantities with whichever models you
trust and pass them to `psychoacoustic_annoyance` directly (the four-argument
function is the exact model).

## 3. Fluctuation strength

**Fluctuation strength** $F$ (vacil) quantifies the perception of *slow*
loudness fluctuation. Like roughness it is a band-pass sensation of the
modulation frequency, but it peaks about an order of magnitude lower, at
$f_\mathrm{mod} \approx 4\ \text{Hz}$ rather than the ~70 Hz roughness peak. By definition, a 1 kHz tone at 60 dB,
100 % amplitude-modulated at 4 Hz, produces 1 vacil. This page covers two of
the three fluctuation-strength models in the library: the Fastl & Zwicker
closed form for amplitude-modulated broadband noise (§3.1) and the Osses et
al. (2016) signal model for arbitrary signals (§3.2). The normative
Sottek-model fluctuation strength of ECMA-418-2 Clause 9, in vacil_HMS, lives
in [Sound Quality Metrics](https://docs.jmrp.io/phonometry/perception/psychoacoustics/sound-quality/);
note that this page's unit is the vacil and that one the vacil_HMS, so the two
are not the same number for the same sound.

![Left: the closed-form and signal-model fluctuation strength of the same amplitude-modulated broadband noise at 60 dB against modulation frequency, both band-pass around 4 Hz, the signal model peaking at 5.5 vacil against the closed form's 3.7, a factor 1.5 overshoot at 4 Hz. Right: the signal model on the amplitude-modulated 1 kHz tone at 70 dB of its Table 1 literature cross-check, peaking at 1.09 vacil at 4 Hz](https://docs.jmrp.io/phonometry/media/fluctuation_strength.svg)

*The two models on the same stimulus, which is the comparison the caution box
below turns into a rule. Both are band-passes centred near 4 Hz, but on AM
broadband noise the signal model overshoots the closed form by about half
again, because it accumulates modulation band by band across the whole Bark
axis. On the 70 dB AM tone of its literature cross-check, right, it behaves.*

**Show the code for this figure**

```python
import matplotlib.pyplot as plt
import numpy as np
from phonometry import psychoacoustics

# Left panel, the two models on the same stimulus: AM broadband noise at
# 60 dB, 100 % modulation.
fmod = np.logspace(np.log10(0.5), np.log10(32.0), 240)
f_bbn = [psychoacoustics.fluctuation_strength_am_noise(60.0, 1.0, fm) for fm in fmod]

rng = np.random.default_rng(3)
tn = np.arange(int(4.0 * fs)) / fs
noise = rng.standard_normal(tn.size)
fm_noise = [0.5, 1.0, 2.0, 4.0, 8.0, 16.0, 32.0]
f_noise = []
for fm in fm_noise:
    am = (1.0 + np.sin(2 * np.pi * fm * tn)) * noise
    am = am / np.sqrt(np.mean(am ** 2)) * 2e-5 * 10 ** (60 / 20)
    f_noise.append(psychoacoustics.fluctuation_strength(am, float(fs)).fluctuation_strength)
print(round(f_noise[3], 1), round(f_bbn[np.argmin(np.abs(fmod - 4.0))], 1))   # 5.5 3.7

# Right panel, the signal model on the AM tone of its literature cross-check
# (Osses 2016 Table 1): 1 kHz at 70 dB, over the same modulation sweep.
t = np.arange(int(2.0 * fs)) / fs
carrier = np.sin(2 * np.pi * 1000.0 * t)
f_tone = []
for fm in fm_noise:
    am = (1.0 + np.sin(2 * np.pi * fm * t)) * carrier
    am = am / np.sqrt(np.mean(am ** 2)) * 2e-5 * 10 ** (70 / 20)
    f_tone.append(psychoacoustics.fluctuation_strength(am, float(fs)).fluctuation_strength)
print(round(max(f_tone), 2))   # 1.09, at the 4 Hz point

fig, (ax, ax2) = plt.subplots(1, 2, figsize=(12, 5))
ax.semilogx(fmod, f_bbn, label="closed form, Eq. 10.2")
ax.semilogx(fm_noise, f_noise, "s--", label="Osses 2016 signal model")
ax.axvline(4.0, ls="--", color="0.4")
ax.set_xlabel(r"Modulation frequency $f_\mathrm{mod}$ [Hz]")
ax.set_ylabel("Fluctuation strength F [vacil]")
ax.set_title("Both models, AM broadband noise at 60 dB")
ax.legend(loc="upper right")
ax2.semilogx(fm_noise, f_tone, "s--", color="tab:green")
ax2.axvline(4.0, ls="--", color="0.4")
ax2.set_xlabel(r"Modulation frequency $f_\mathrm{mod}$ [Hz]")
ax2.set_title("Signal model, AM tone at 70 dB")
plt.show()
```

### 3.1 Closed form for AM broadband noise (Eq. 10.2)

For sinusoidally amplitude-modulated broadband noise, Fastl & Zwicker give a
closed form (Eq. 10.2) in modulation factor $m$, level $L$ and modulation
frequency $f_\mathrm{mod}$:

$$
F = \frac{5.8\,(1.25\,m - 0.25)\,[0.05\,(L/\mathrm{dB}) - 1]}
{(f_\mathrm{mod}/5\,\mathrm{Hz})^2 + (4\,\mathrm{Hz}/f_\mathrm{mod}) + 1.5}\ \ \mathrm{vacil}.
$$

The denominator is the 4 Hz band-pass: it bottoms out near
$f_\mathrm{mod} \approx 3.7\ \text{Hz}$ and
rises on either side. The result is clamped at 0 (the sensation vanishes below
~20 dB or $m < 0.2$). This exact form is the value to quote for AM broadband
noise.

```python
from phonometry import psychoacoustics

print(round(psychoacoustics.fluctuation_strength_am_noise(60.0, 1.0, 4.0), 4))   # 3.6943 vacil
```

### 3.2 The Osses 2016 signal model

`fluctuation_strength` implements the Osses et al. (2016) signal model: it builds
an excitation pattern over 47 auditory filters, extracts the ~4 Hz envelope
modulation per band, weights and combines it, and returns the overall $F$
(vacil) plus the specific fluctuation strength over the Bark axis and the
time-dependent trace.

```python
from phonometry import psychoacoustics

res = psychoacoustics.fluctuation_strength(x, fs)
print(round(res.fluctuation_strength, 2))   # 0.65 vacil for the signal above
res.plot()   # specific fluctuation strength F′(z) over the Bark axis (needs matplotlib)
```

![Specific fluctuation strength over the Bark axis for a 1 kHz tone at 70 dB SPL fully amplitude-modulated at 4 Hz: the sensation is concentrated in the critical bands around the carrier near 8 Bark and integrates to about 1.1 vacil](https://docs.jmrp.io/phonometry/media/fluctuation_strength_specific.svg)

**Show the code for this figure**

```python
import matplotlib.pyplot as plt
import numpy as np
from phonometry import psychoacoustics

# The reference-like stimulus: a 1 kHz tone at 70 dB SPL, 100 % amplitude
# modulated at 4 Hz, where the sensation peaks.
fs = 48000
t = np.arange(int(2.0 * fs)) / fs
am = (1.0 + np.sin(2 * np.pi * 4.0 * t)) * np.sin(2 * np.pi * 1000 * t)
am = am / np.sqrt(np.mean(am ** 2)) * 2e-5 * 10 ** (70 / 20)
res = psychoacoustics.fluctuation_strength(am, float(fs))
print(round(res.fluctuation_strength, 2))    # 1.09 vacil

# One line: the specific fluctuation strength over the Bark axis.
res.plot()
plt.show()

# Or draw f'(z) by hand from the arrays the result carries:
fig, ax = plt.subplots()
ax.fill_between(res.bark_axis, res.specific, alpha=0.3)
ax.plot(res.bark_axis, res.specific)
ax.set_xlabel("Critical-band rate z [Bark]")
ax.set_ylabel("Specific fluctuation strength [vacil/Bark]")
plt.show()
```

The sensation stays where the modulated energy is, in the critical bands
around the carrier, which is exactly why the closed form of §3.1 and the
signal model diverge for **broadband** modulated noise: there the modulation
is spread over the whole Bark axis and the band-by-band model accumulates
more of it than the single closed form allows.

**Note**

**No numeric standard.** Fluctuation strength has no ISO/IEC standard. This is a clean-room
implementation from the Osses 2016 paper, calibrated so that the
1 kHz / 60 dB / $m = 1$ / 4 Hz AM tone reads 1.00 vacil by construction, and
cross-checked against the Osses 2016 Table 1 literature values and the open SQAT
reference (used only as a numeric oracle). Over the 70 dB AM-tone sweep
$f_\mathrm{mod} \in \{1, 2, 4, 8, 16, 32\}\ \text{Hz}$ it gives
`[0.40, 0.79, 1.09, 1.05, 0.17, 0.09]`
vacil against the literature `[0.39, 0.84, 1.25, 1.30, 0.36, 0.06]` (Pearson
$r = 0.98$, correct 4 Hz peak, within ~2.1×). FM-tone accuracy is explicitly not
pursued. For **AM broadband noise** the signal model overshoots the absolute
level (it spreads the modulated energy across bands); quote the closed form
`fluctuation_strength_am_noise` (§3.1) for that stimulus.

A steady signal does not read zero, because of the framing the scope below
describes:

```python
import numpy as np
from phonometry import psychoacoustics

fs = 48000
t = np.arange(2 * fs) / fs
tone = np.sin(2 * np.pi * 1000 * t)  # 1 kHz, unmodulated, set to 70 dB SPL
tone *= 2e-5 * 10 ** (70 / 20) / np.sqrt(np.mean(tone**2))
noise = np.random.default_rng(0).standard_normal(t.size)  # broadband, 60 dB SPL
noise *= 2e-5 * 10 ** (60 / 20) / np.sqrt(np.mean(noise**2))
steady_tone = psychoacoustics.fluctuation_strength(tone, float(fs))
steady_noise = psychoacoustics.fluctuation_strength(noise, float(fs))
print(round(steady_tone.fluctuation_strength, 2))   # 0.09 vacil
print(round(steady_noise.fluctuation_strength, 2))  # 0.15 vacil
```

## What this guide covers

- **Covered.** Fastl & Zwicker's *Psychoacoustics: Facts and Models* gives the exact $PA$
  model, Eqs 16.2-16.4 (origin Widmann 1992), run by `psychoacoustic_annoyance`.
  It also gives the closed form for AM broadband noise, Eq. 10.2, run by
  `fluctuation_strength_am_noise`. The Osses et al. (2016) signal model for
  fluctuation strength runs as `fluctuation_strength`, cross-checked against its
  Table 1 literature values and the SQAT reference.
  `psychoacoustic_annoyance_from_signal` derives the four inputs from a signal
  (ISO 532-1 Zwicker $N_5$, DIN 45692 $S$, ECMA-418-2 $R$) and combines them
  with the exact model.

- **Not covered.** The Osses 2016 model's accuracy for FM tones is explicitly not pursued. Only
  AM stimuli are validated here. The front-end also departs from the paper's
  exact framing: its 2 s frames with 90 % overlap and its screening against the
  absolute hearing threshold become 50 % overlap, a Hann window and relative
  floors here. As a result, a steady 1 kHz tone reads about 0.09 vacil instead
  of 0, and steady broadband noise reads about 0.15 vacil, partly the
  physical level fluctuation of the noise itself. For AM broadband noise, quote
  `fluctuation_strength_am_noise` (§3.1) instead of `fluctuation_strength`,
  which overshoots that stimulus. The normative Sottek-model fluctuation
  strength of ECMA-418-2 Clause 9 is not implemented on this page: it lives in
  [Sound Quality
  Metrics](https://docs.jmrp.io/phonometry/perception/psychoacoustics/sound-quality/).

## See also

- [Loudness](https://docs.jmrp.io/phonometry/perception/psychoacoustics/loudness/): the ISO 532-1
  percentile loudness $N_5$ this model takes as its first argument, and the
  acquisition rules the recording has to satisfy before any of it applies.
- [Sound Quality Metrics](https://docs.jmrp.io/phonometry/perception/psychoacoustics/sound-quality/):
  the DIN 45692 sharpness $S$, the ECMA-418-2 roughness $R$ and the normative
  vacil_HMS fluctuation strength of the same sensation this page models in
  vacil.
- [Advanced Loudness](https://docs.jmrp.io/phonometry/perception/psychoacoustics/advanced-loudness/):
  the alternative loudness models, and why mixing families makes the composite
  an engineering estimate.
- [Environmental Levels](https://docs.jmrp.io/phonometry/environment/assessment/environmental-levels/):
  community annoyance, the other thing the word means, and the rating levels it
  is assessed with.
- Theory: [Advanced loudness models and sound quality](https://docs.jmrp.io/phonometry/reference/theory/perception/#advanced-loudness-models--sound-quality): the loudness and sound-quality metrics the annoyance model combines, derived one at a time.
- API reference: [`psychoacoustics.quality.annoyance`](https://docs.jmrp.io/phonometry/reference/api/psychoacoustics/annoyance/) and [`psychoacoustics`: fluctuation strength](https://docs.jmrp.io/phonometry/reference/api/psychoacoustics/fluctuation-strength/).

## References

- **Fastl, H., & Zwicker, E. (2007).** *Psychoacoustics: Facts and models* (3rd ed.). Springer. https://doi.org/10.1007/978-3-540-68888-4
  The source of the psychoacoustic-annoyance model of section 2 (Eqs 16.2-16.4, chapter 16; origin Widmann 1992) and of the closed-form fluctuation strength for AM broadband noise of section 3.1 (Eq. 10.2, chapter 10).
- **Felix Greco, G., Merino-Martínez, R., Osses, A., & Lotinga, M. J. B. (2025).** [*SQAT: A sound quality analysis toolbox for MATLAB*](https://github.com/ggrecow/SQAT). GitHub. https://doi.org/10.5281/zenodo.7934709
  The open MATLAB reference (open-source software) used as the numeric oracle for the fluctuation-strength cross-checks on this page.
- **Osses Vecchi, A., García León, R., & Kohlrausch, A. (2016).** Modelling the sensation of fluctuation strength. *Proceedings of Meetings on Acoustics*, *28*, 050005. https://doi.org/10.1121/2.0000410
  The fluctuation-strength signal model implemented in section 3.2 (presented at ICA 2016; clean-room, with no numeric standard, calibrated to 1 vacil at the reference AM tone), including the Table 1 literature values used as its cross-check.
